Deleted
Deleted Member
Posts: 0
Likes:
|
Post by Deleted on Oct 15, 2016 14:43:52 GMT -6
A few more "updates" on this build..... Not much, but something, something meaning a bit of "small" details ready to go! I too kit upon myself, to make my own "power steering" on this model just I did on my truck in this build, as the kit, neither of them, came factory or stock with such, and me, being me, I LOVE details, so I just HAD to add it! With that being said, a part that came from the stock pil 'O parts I got, I salvaged the lower power steering, that leads to the drag link. Granted, as you can see the white is the power steering "housing", that I had to remove the steering shaft from one end, and make it go on the other (NOT added here), with that, I needed to make the drag link, which is that metal "dog bone" detail seem here as well as "pin" it to the steering box, and have some sort of "spacer" as well, which is out of a necklace kit I bought for numerous detailing uses.... Fittings, spacers, you name it. Same thing different view. To show "depth" of the detail in itself. It will be mounted OUTSIDE the drivers side frame rail! As you'll see. Remember this truck is a bit different from the common "Power Wagon" we all know and love! I got a bit done/added to on the frame as well. I went and am still working on the rear suspension to get it "level" as it was all broken up.... NOW however its being done with heat! As they're solidly, mounted in place on the frame for the rear axle! BUT, I got to thinking AFTER mounting the rear leaf springs, what about the transfer case!? Hows that going to "sit" on a "low" 4x4 truck? As the actual model itself, seems to have been "lifted" and I brought it back down to "family 4x4 truck" standards.... I did NOT want the transfer case to sit so low that it was barely off the ground, BUT to sit in such a way, it wasn't to far up in the frame to cause alignment problems to the cab with the interior tub. SO, I got to looking a bit and needed to make some more modifications, to the frame. The dark gray part is the transfer case mount. The whole square inside the frame rails, and the webbing" between the cross members had to be removed. As I needed the thickness of the frame to get the new transfer case mount in it! And "high" enough to look right. I even went as far to relocate the transfer case "cross member" mount, to the HIGHEST location of the locating blocks on the insides of the frame rails. To look as an "angle" mount from the cross member part of it, (if any of this makes sense) Then while messing, I went to "sturdy" up the rear leaf springs. These things were/are brittle as they're old, and I MEAN OLD, and were from a Glue bomb I mentioned I got for mere parts. A LOT of little things, to allow me to move on to the bigger things..... MORE to come just after these brief messages!
|
|
Deleted
Deleted Member
Posts: 0
Likes:
|
Post by Deleted on Oct 15, 2016 14:44:28 GMT -6
Now, a LOT of really little work all on one sub-assembly of the truck. The front axle! Brake lines, hard line and hose and fittings, you name it. I made my own front disk brakes with added calipers from another glue bomb I had.... All to be put together on this truck to make it look the part. Just like my Power Wagon, earlier in the build, I had to make A LOT of the axle parts myself, as I do not think nor believe details as such are even made for us in this hobby BUT, I'm not complaining, I'm saying it as I enjoy seeing just hot far I can push myself, to make different details like this! Passenger side tire, rotor, brake, all the lines and ALL the fittings for that side, as well as brake line "hard line" to mount made and placed on rear differential casing.... The "hard" brake line in silver, has a mid-line "T" fitting to have the line front the master cylinder come down to it from a hard line ALSO to have a fitting to have a hose to meet this "T" fitting...... A LOT of "line-work", hard piped, and fittings to hose and such..... the "hose" you'll see from me, won't be "braided" its all as factory in this builds, as "rubber", right to the brass fittings that I make myself! Just the other side.... Same side bit better view maybe..... You can see my rubber brake line hose from the hard pipe on the rear, to the caliper on the rotor! In these views, you may be able to also see, the "mount brackets on either side from the ends of the hard pipe to the hose that goes to the calipers..... The hose is needed for the knuckle movement of the steering axle. A bit better side-to-side of the axle, showing a good view of the mid-line "T" that will connect to a hose that goes to the master cylinder. Over all view..... Not to bad for a couple hours work! Front axle is ready to be installed on the truck frame! BUT I have to get the rear one in the same shape first as then after that comes the shocks to the suspension, for the front. (Those shocks I didn't use on my truck), may come into use on this truck remember this one is stock height, my truck wasn't stock height! -We'll see! I'm pleased so far! More to come as I've made progress! ENJOY!
|
|
Deleted
Deleted Member
Posts: 0
Likes:
|
Post by Deleted on Oct 15, 2016 14:44:57 GMT -6
So as I promised, MORE progress has been made..... To start out, as you all VERY WELL KNOW by now, I have a few of these trucks! (3).... BUT because of the difference from one to the other, I had to find ways to make things "happen"..... This is where it gets FUN! I went and looked through the parts I had for the "stock" frame to the short step-side bed truck (I wasn't going to be using this frame on my "Dads" truck, I did however use the stock frame on my truck!) BUT that was due to Dads having a long 8 foot "straight" bed (Sweptline is what Dodge called them). But anyway, the frame on Dads truck I choose the resin version I had, as I need the styrene version for HEAVY frame modifications on the frame rails to handle a utility bed. Meaning, the factory frame that came with my Dads truck model was of the short step-side bed, and wasn't going to be used on this particular truck! WHICH, is what I'm getting too here. That short frame, I needed the inner fender wells from it, to fit onto the resin frame (was resin cast without them) SO, I get out my handy razor saw, only to find that particular blade too wide to make the cuts needed to remove just the inner fender wells, without "hurting" the frame all too bad (I want to save it for a rainy day!) SO, off to look for a more suitable way to remove them, and went looking through my handy blade selection I have for thee ole Exacto knives I got.... Found a "keyhole" type blade, thin and pointy at one end with some serious teeth on it. Will do the trick! I get out my pin vice, drill a hole just big enough to whittle the keyhole blade, in through it to begin "sawing"..... Here is the frame, BEFORE I began all this: Clean, nicely cast, it ought to donate well to the cause.....and it did! Left the frame a little bit of a mess (I'll have to clean it up), BUT it donated the inner fender wells I need for Dad's truck...... BOTH inner fender wells, came off nicely, and I got one cleaned up right away to see what all might be involved, I'm glad I choose to do this the way I did, I kept the donor frame for something later, and gained the needed inner fender wells for under the hood of my Dads truck in this build! More to come right after these short messages! ENJOY!
|
|
Deleted
Deleted Member
Posts: 0
Likes:
|
Post by Deleted on Oct 15, 2016 14:45:19 GMT -6
-So, while I was thinking on how I was gonna go about the added inner fender wells, I got to thinkin', I probably ought to get that steering box on the outside of the drivers side frame rail, as once the inner fender well is in place, getting to that or making the inner fender well fit, this be thee BEST time to get that in place! A picture to show a bit of "depth" of the actual added detail: Then in these pictures I went ahead and did some fine "clean-up" of the edges around the wheel openings in the floor pan to take the inner fender wells without a problem.... The seen pencil line on the frame rail "side" is the location of the CENTER of the axle placement on the suspension, to center the wheel in the opening, and center of the fender itself on the body, and be even on both the front and the back, spacing. This WILL disappear when the frame and underside is painted, BUT will guide me, when I go to tape off the location as to where the axle will glue to the leaf spring, and allow me to glue it in place when the time comes. ALL the mounting locations will be taped off before the frame is painted! EVERYTHING is looking good about now! SO, stay tuned! More to follow!
|
|
Deleted
Deleted Member
Posts: 0
Likes:
|
Post by Deleted on Oct 15, 2016 14:45:53 GMT -6
Then once I sat the frame aside, I began trying to "fit" the passenger side inner fender well in place on the frame. Only to find that the stock resin cast opening, was to large to add it as I removed the plastic one from its frame. I wasn't going to cut the floor pan of the plastic one, in order to fit it here, (be difficult to mud it in to look the part, SO, I went and added shim plastic to the inner fender wells, and a small section of angle plastic, to "glue" to the adjoining floor pan! They look a bit rough, had filed the first one (passenger side) right after its removal and before the drivers side was removed.... One filed up nicely and one was removed, and then this picture was taken! Contoured GREAT, and corners "notched" to fit around the frame rails! Un-cleaned edges on the angle plastic mount..... BUT it is notched here too! Then came the FUN..... The drivers side! REMEMBER I added that steering box? WELL because of my "detail adding ways" I had a fun time contouring this one, as with my truck in this build, I added power steering lines from the pump on the engine, to the steering box, mounted to the frame! And whats stopping me from doing that same thing to this model? Absolutely NOTHING! SO, having said that, I had to contour the inner fender well on the drivers side, to accommodate both the power steering box, on the frame, AND the power steering lines from the engine, as well as the steering shaft from the steering wheel!!! I added that also to my truck! It got that treatment as well as the added shims, and angle mounts on both ends! I have to say "contouring" wasn't too bad to get the inner fender well to sit in the same contour as the frame, the contour trouble area was where that steering box was, BUT, I managed to get it to fit and look good all at the same time. MOST of this detail for mounting purposes, will disappear when the truck goes together as the rear will be covered by the firewall, as well as the front with the radiator core support, and all the detail on it, BUT, is needed "extras" to mount solidly to the frame! Front of the driver side fender well...... Cleanly done, and ready to be put in place! More to follow!
|
|
Deleted
Deleted Member
Posts: 0
Likes:
|
Post by Deleted on Oct 15, 2016 14:46:22 GMT -6
OK now that BOTH inner fender wells were removed from the donor frame, and cleaned, and then sat up for installing, I got right to it..... Looking at it from the passenger side of the truck, you can see the opening in the fender well to allow me to add a steering shaft from the steering wheel, as well as all the pipe work from the power steering pump on the motor. Looking from the drivers side.....Granted, BOTH these pictures show the "open" corners.... I have to go back and "fill" those in. ONLY the opening for the steering will be open when all said and done! Coming up next, is something NEVER done.... These 2 trucks had never seen each other unless in passing, I took the 2 models to see if the height from one to the other was good for both trucks "stance"!!!!! Stay tuned!
|
|
Deleted
Deleted Member
Posts: 0
Likes:
|
Post by Deleted on Oct 15, 2016 14:46:48 GMT -6
As I mentioned in my last post, I HAD to see what the stance was between the 2 trucks..... My Power Wagon on the left, Dad's Adventurer on the right! Under a bit more light...... I say, the stance is PERFECT, my truck was built to sit high, as it was, the real ones were about as you see these 2 models, Dads truck on the right, needs a bit of work to get it where my Power Wagon is, BUT I think this is GREAT!!!!! Mine was was built purposely to sit high (I wanted to go muddin' in it) Dad's was a "family 4x4 truck" and sit at a high "stock" height as he added slightly bigger tires and rims to his..... I'm VERY pleased with this work so far, on BOTH trucks! Got a ways to go on my Dad's, BUT it will happen.... I got to sit and detail up the rear axle for his and then figure out its suspension as well as shocks for both..... Ought to be a fun task! SEEING these last few pictures of both trucks front-to-front like that...... WOW! As always, more to follow as things are done! ENJOY!
|
|
Deleted
Deleted Member
Posts: 0
Likes:
|
Post by Deleted on Oct 15, 2016 14:47:12 GMT -6
Well after a bit of time and a good weekend to keep me out doors a bit, I actually got a bit done to the truck in the evening! So, without going on an on, hows about a look see to what I did!? Seen here, all "clear coated" shiny... Frame got painted, and clear coated! Sadly, however the paint on this frame is a bit "odd" looking. I think due to the frame being resin for one, and 2, the paint when I went an cleaned up the air brush, seemed a bit "think" I guess, as it was left over from a pre-mix I done a while ago.... Was flat paint, and With my dad he had "undercoated" every vehicle he owned so..... The frame got a slightly different treatment, I'm not sure what that was to consist of, BUT was flat black as told to me by my uncle! SO, with knowing that, I clear coated the flat black frame, and then allowed that to dry and went back and dry brushed dullcote onto the just the frame rails and cross members. Dullcote added to the frame and cross members! More to follow these short messages!
|
|
Deleted
Deleted Member
Posts: 0
Likes:
|
Post by Deleted on Oct 15, 2016 14:47:57 GMT -6
Then while at that painting, on the frame, I got the steering box, painted and detail painted, all in the while AFTER the spray painting was done, as the steering box would have been a cast iron steel color. Which, was unpainted like the color of a unpainted transmission (they're normally a matching color of bare cast iron) Then a bit different view showing detail painting I did: These 2 pictures show the gloss black bell crank that needs a ball joint, rod to go from the open hole, to the jointing, steering bell crank, on the axle spindle.... I have yet to make this part.... This won't be made to fit till the axle is ready to go into place on the front suspension! More to follow after these short messages.... Enjoy!
|
|
Deleted
Deleted Member
Posts: 0
Likes:
|
Post by Deleted on Oct 15, 2016 14:48:16 GMT -6
While that was all setting and curing drying paint, or glue.... I got the transfer case loose from the donor frame, to refurbish to usable standards. Just like the transmission will be and the steering box, the transfer case would have also been a cast iron color of steel. Cast-on detail wasn't real bad, BUT it needed something more..... A good ole oil/grease pan was needed (factory detail part was merely "flat" and was a 2 part detail all together, With the added "pan" detail painted bare steel color, as it would have been, I made the part from 2 small sections of plastic sheet, one thicker then the other as the "lip" would not have been real thick anyway, BUT the sump in the pan, would have been..... I have yet to add one last detail to this part, as it needs a drain cock for transfer case fluid changes..... Short message, more to follow this one!
|
|
Deleted
Deleted Member
Posts: 0
Likes:
|
Post by Deleted on Oct 15, 2016 14:48:33 GMT -6
SO, as I had firstly spoke to the uncle, this truck of my Dads, got some decor, added to it, firstly (I should have known) was the stock valve covers, removed, and replaced with chrome ones that were OEM chromes covers that were Mopar made..... Then if you look, I added the distributor, and the exhaust manifolds. This truck, unlike mine kept single side exit exhaust. Meaning, I will have to make a cross-over pipe to go from the passenger side manifold, the the drivers side, in a "Y" pipe..... Not sure what oil filter Dad may have used over the years, BUT I added mine to his truck as tho it was a OEM "Mopar" replacement part, in white. IF I can find a "Mopar" oil filter decal, before the engine is ready to go into place, I may add it to the part.... If not, "white" is good enough as the decal depending on location, wouldn't be easily seen anyway! The other side of the engine, missing the exhaust manifold, it was drying when this picture was taken. I did however get the starter in place, and if you look closely, you can see the carburetor linkage and return spring in place. The one thing this truck have had, was the California Omissions items, I KNOW without asking anyone that my Dad had removed these, (wasn't required to be inspected in the state of Pennsylvania.) SO, those parts will be omitted from the build! A shot of the back of the engine. I have to add the PCV valve, and hose, as well as some other small things. I have to add the transmission fluid dip-stick not seen here, as well as paint the transmission, (I wait till last to paint the transmission as I use it as a "handle" to hold the engine while detailing it.) A NICE head on view of the engine. A Mopar 360 4 barrel..... I need to get the holes drilled for the plug wires, and add in wire looms.... Those are next to be completed! -I also need to make an oil dip-stick that will be added to the left side of the front, of the engine. A short and sweet update to follow....
|
|
Deleted
Deleted Member
Posts: 0
Likes:
|
Post by Deleted on Oct 15, 2016 14:48:53 GMT -6
And for now..... Last but not least, I was working on the frame and got to looking, theres a nice location for the spare tire! I took the last tire I had,and got it ready for a spare on Dads truck that will be placed in the stock location.... The tire however, wasn't the best tire, the hole was trimmed (or so it looked) that the rims I needed to put into it would not fit, SO, that gave me the idea to take this 5th tire I had to make an actual detail part with it! Dad himself, did not have a matching rim for the spare, BUT what he did do, was take an old Steel wheel, and have it painted, (NOT sure if it was paint, or if he had it powder coated like he did with the spoke'd rims) But it was in fact "white" so..... I took a spare one I had a as an extra, that matched no other steel wheels I had, painted it white and it got glued into a matching tire...... Rim glued in, center drilled out..... looks pretty good! My next treat to this, is drilling out ALL the lug nut holes! It would have any lug nuts on it, as a spare, right? ENJOY for now! More to follow when progress is made!
|
|
Deleted
Deleted Member
Posts: 0
Likes:
|
Post by Deleted on Oct 15, 2016 14:49:23 GMT -6
SO..... it has been a few days, the rain stopped and the weather got nice, and ole John had some out door stuff to do and yet got more to continue out doors but I did get a little done! I took the engine and got the plug wires, and boots in place.... I also got the valve covers on the engine too (I almost forgot that the last I posted), the engine had no valve covers or anything for details up top! The valve covers ALSO got wire looms mounted to them to hold the plug wires! The wire looms are how I "directed" the wires to lay as they are too! Just the opposite side! Back of motor, showing the coil wire "loose".... BUT the coil in place! (The coil, is a in-shop made part! This model (just like my truck in this build) did not come box-stock with a "coil" detail.... The "silver wrap" (mount in real life) was made using scrap BMF! Coil wire in place! Up next, is short and sweet (I did not get a lot done to the build so far this week), but one more post to follow, right after these short messages!
|
|
Deleted
Deleted Member
Posts: 0
Likes:
|
Post by Deleted on Oct 15, 2016 14:49:46 GMT -6
Last for now..... I began replicating the firewall. Just like how mine looks, Dads truck was pretty much the same! A little bit of wire being done, BUT a lot of holes drilled for wires from the engine, and hoses for the heater.. and battery lines as well.... This is almost ready to have it "fitted" to the frame, like mine was done in my truck! BUT a little detail yet to be done and some touch up paint as well! Thats it for this quick update, but I guess, something is better then nothing! ENJOY!
|
|
Deleted
Deleted Member
Posts: 0
Likes:
|
Post by Deleted on Oct 15, 2016 14:50:01 GMT -6
So a little update, not much mind you, but a little..... As you all should know by now, I'm remodeling my shop, and most of the work benches..... Which will make model building and all a bit easier once done! BUT, in the evenings when the noise has to cease, I work on Dads truck in this build, just to keep it going, and not stop on it completely..... SO, what I have done was searched out a "junk" drive shaft, as Dads truck would have had whats known as a Divorced transfer case, meaning it had 3 drive shafts! One from the transmission, to the transfer case, and then one each, to the front axle and one to the rear axle. The transmission would NOT be bolted to the transfer case on this truck, as it was on mine! BUT, because, I didn't want to cut up a good one, I took the donor frames "front" drive shaft (not the best of quality of details), BUT had half ways decent "u-joints" to be salvaged from it to make the needed one to go from the transmission to the transfer case! REALLY short one I might add, there is no real "shaft" to it..... Mostly all "U-joint" detail! Notice, the engine? Its upside down! WELL I had to get the plug wires to the locations in the head in order to make this part happen, the loose plug wires would NOT have allowed me to flip it over like this to "fit" the first drive shaft to the frame! SO, that was a pre-step, I had to do in previous postings of the build, as it all goes together like a jig-saw puzzle! Thats it for now, More to come on this build as I am able and have the shop in somewhat of a orderly fashion! (I got my work cut out for me!) Enjoy, for now.....
|
|
Deleted
Deleted Member
Posts: 0
Likes:
|
Post by Deleted on Oct 15, 2016 14:50:31 GMT -6
Well guys, As you all know, I have been busy..... Before Fathers Day, as well as this past Thursday, a few know I was in the hospital for a day procedure that came out OK, I'm a bit sore, but to have a stent added to either leg is a bit of a task on the person having it done so. but anyway, I'm doing good and feeling "OK" just a little sore" but handling it pretty well..... As you all know (or so I thought I've mentioned) I lost my Dad a little over a year ago, now (was a year in March) SO with that, and have had thoughts of him on my mind with the builds a few of you of/from me, this Father & Son build was directed towards this whole thing, and Fathers Day, all I wanted to do was relax, (because I had too) and work on my Dads model in this build (because I could), in honors to him, and thats just what I did! This is one of those postings, to show a little of a lot of little parts, small details that will lead to much bigger sub-assemblies in the near future! So with that, I got to thinking how the rear axle needed to go together, and got to looking at where I left off on it. THEN before getting into that looked over the frame to see where I was on that (kind of "reflecting" past work), and where to "pick up" again, so-to-speak.... So, I took the frame, and thought,A LOT had to go onto my trucks frame in this build BEFORE the axle could be placed onto it, (I WAS NOT going to attempt working around a mounted rear axle!) Very "end" of the rear brake line. This is the "hard" line that goes to the mount seen mid-frame, to a fitting, that will run forward to the brake master cylinder lower manifold.... The hard pipe itself, has a fitting on it, that carries it through the little angle iron bracket on the frame cross members! This line was made formed and placed for the picture. I had been removed, painted and let dry before gluing in place! The fitting is now brass colored, and the line is steel colored, as these had steel brake lines! Just like my model trucks frame in this build, the brake line will follow the inside of the frame rails, in the corner of the frame, where it meets the floor boards, all the way to the front. My trucks frame was built this very same way! Only difference is Dads truck was 2 scale feet longer then mine! (He had a full size bed "Sweptline" so.... mine was Step-Side short box. As you can see, I went through drilled need mounting holes, and got the copper line ran to be in place, got it all fitted, and then, removed it all to paint: Which means, this step to getting the rear axle in place is complete! NOW, I got to get the engine in place, with all the exhaust pipes in place in order to get the axle onto the rear suspension! I got a ways to go! (Thats what I get for taking the time to remodel my shop!) BUT the things I have done in it to date, has been much easier, much more user friendly, and way more comfortable to do with it set up as I have it! -SO, that alone makes the time WELL worth the effort involved! -HOPEFULLY LESS "make shift" tables in the near future (Unless they're in MY WIFE'S side of the shop, then, I don't care!) LOL Engine work coming up next! ENJOY....
|
|
Deleted
Deleted Member
Posts: 0
Likes:
|
Post by Deleted on Oct 15, 2016 14:50:56 GMT -6
Well as I mentioned, Engine work was up next...... I had to add a oil dipstick to the 360 in this truck, which was a fun added part (I make them, myself, paint the "tube" install, into/through a left over wire loom and done...... The "chrome" loop is just in front of the valve cover, difficult to see, BUT you can see the shadow of the wire itself, on the engine block, just behind the fuel line! Very fine black line. I will attempt to get a better picture of this next time I snap pictures its such a small detail part! Then, what took the most "patients" was the engines pullet and belt set up..... What a task! I needed to incorporate the following: Water Pump Alternator Power Steering Air Conditioning Crank and a single tension pulley What FUN that was! I took a few "glue Bomb parts, broke factory belts, and removed them, chucked the pulley in the Unimat and left 'er rip.... Spinning the pulleys back "round" again, to wrap Evergreen Styrene around them (as belts) for strength, and then flattened the outer most pulley glue bomb, to use to over lay it onto the rear ones, and make it all fit and look the part..... I *THINK* I managed to get 'er done! Blue pulley to be the crank pullet, black one to be the water pump pulley, the very highest mounted one A/C Compressor pulley, silver to the left of the AC pulley is for the Alternator, and off to the right is power steering MID-mounted silver pulley a tensioner pulley. I'm NOT 100% sure how this was to all be under the hood of my Dads truck, BUT because his was "stock" and NOT trusting on-line sources as being 100% honest to the stock location, I set it up as best I knew how and look right..... Got to remember this truck is/was after all a 1979 model Dodge! A LOT can be changed over time so..... SO, I tend to go with what little I know added to the know-how on my own truck was, and thinking how it reflect on a slightly different truck a year newer..... I do think however, I pulled it off! -It really isn't a "detail" thats going to be fully 100% seen when all said and done ANYWAY, so only needs to "look" the part 100% top end! -Which, that I know is 110% accurate! Tedious little details done, MORE to come as I'm able! Enjoy!
|
|
Deleted
Deleted Member
Posts: 0
Likes:
|
Post by Deleted on Oct 15, 2016 14:51:48 GMT -6
So, on Fathers day, and a little bit yesterday, and more will come after tonight..... I did get some done, but could not "handle" for pictures and so, had to wait till I could..... Our very own "Stray" had posted pictures of his "spare" wheel on a build, and his persistence, on showing me what he had done, I simply did it on this build! I wasn't originally going to "open" the "slots" in the steel rim, BUT....... He persuaded me to do and do it just for looks sake! And with that here is how mine turned out! (THANKS for the inspiration Stray!) I took this: To this: With flash ---^ Without flash ---^ I think it came out GREAT! I like how it looks even tho when all said and done, and in-place on the truck it won't be easily seen! BUT, theres more..... Me, being well, ME, I took it a STEP further! The truck, has to have a spare tire mount, in the "stock" location under the rear portion of the bed..... SO, I took the frame, and began measuring to make one...... Right now, it doesn't appear to be much, BUT ohhh yeas it is! This "pole" is mounted to a resin frame, NOT glued, its machine screwed to the frame! This will hold it in definitely, BUT I plan to also "glue" it to keep it from rotating over time, WHY? WELL thats why I say its something "more"..... The Spare tire WILL BE REMOVABLE! Once all is done and the mount detail is all added to the pole itself, I plan to go back to where it screw mounts and totally fil in the head of the screw in the top side of the frame thats fitted by means of countersinking the screw and all and will be covered and buried in the frame itself, NEVER to be seen again! I have yet to paint this as I have some angle plates to add to it to date, so is left bare machined white styrene. Tire "in-place". just setting there for now! I have to make the cross bar that will have a screw that will thread down into the mount pole that will "pin" the rim with tire to the under side of the bed, AND look as tho it can be removed with a 1/25th scale hand! NOT a screw driver! I however do have a little detail to add to this and then after that it all will get painted. Exception to painting will be the underside of the cross bar that will hold the tire by means of pressure to the rim, I do NOT want the cross bar to have black paint get onto the white rim! SO, only 3 sides of that cross bar will be painted! More to follow, stay tuned!
|
|
Deleted
Deleted Member
Posts: 0
Likes:
|
Post by Deleted on Oct 15, 2016 14:52:17 GMT -6
So while I was working on the engine, and working on the spare tire, I also got to thinking WELL I've got the frame near ready for the rear axle, so why not assemble and detail it as for when I am done with the frame, I'll have the rear ready to go right onto the suspension! SO, I did..... Now, as you all reading should know by now, I had been taking parts from a Donor frame, to make all this happen, this rear axle came from that donor frame! Thing is, even in good shape, it was still too narrow to fit right and look right, SO, I had to widen it just a bit 3/32ns per side to get the width right.... BUT the issue with that came along as I was not using the stock rims or wheel backs! Meaning, I had to make a lot of my own parts to have this all come together. The wheels in the tires and the wheel backs used left NO rear brake drums! I had to turn my own brake drums, to fit the application. Which you'll see better views of in just a bit. BUT adding all that, plus having the narrow axle issue, I had to fit the axle casing with a turned "addition" to get the width right so it went from 3/32nds inch to something to the tune of 5/64th inch to get it close.... SO, I turned one longer piece about 2 and 1/2 the needed length that way I had the same diameter addition for both sides! OR some for error..... Once I had all that assembled and ready to go, the detail adding was next! I took the rear, and added "L" angle brackets to hold the hard brake line plumbed on the rear axle, to these brackets on either side, drilled and then fitted with the pipe itself. Once glue was dry, I took and then fitted the ends of each with fittings, and ran into the rear of the brake drum housing. And then let alone to dry, for an hour or so, and once ready, slid the fittings to their proper locations in the line CA glued them, and let that to dry.... Once dry ALL got painted in-place. Brackets painted gloss black to match that one the rear axle. The lines painted steel, as per factory Mopar. And fittings painted brass, as per materials they're made from, and then from the brackets to the brake drum housing "rubber" for hoses...... That large "brass" fitting seen next to the rear axle "pumpkin" is the fitting that will have a hose running from it, to the little cross member bracket fitting on the frame that will have a hose going from one location to the other. You can reflect this detail on my truck in this build, both were the same but slightly different. NOT by a lot tho..... I think mine was on the other side of the pumpkin, but the frame bracket was in the same location..... Other side, same thing..... Over-all it looks really good! Detail is spot on to a real truck of the same type and everything is just...................... pleasing to date! I'm happy thus far with everything...... Then as you all know, I made my own belt system set up for this truck, last you seem there was no power steering pump on the belt cluster, that has been remedied..... I got to paint the "cap" to it flat black, and this whole detail assembly will be ready to go onto the engine! One step closer to getting the engine in the bay..... THEN I'll be able to begin running exhaust pipe! Thats it for now, more to come when progress happens! Enjoy!
|
|
Deleted
Deleted Member
Posts: 0
Likes:
|
Post by Deleted on Oct 15, 2016 14:52:50 GMT -6
Well its been a little since I've added any updates. Just a few "short" ones, but no less........"PROGRESS"!!!!! SO, As you guys know my last posting, I was working on making a removable spare tire mount. WELL, its done, and on the model! Took a bit to figure out how I was going to go about it! But, its in-place! The "pole" was turned on the lathe as you know, but the ring base, was a part I had to drill out a center hole, and then pop the scrap through a hole punch to get the roundness of it, slightly filed the hole as the drill bit I used was undersized, so I could "fit" the part to the pole and then off to glue it to the frame as well as the pole with a good CA on the trucks frame (remember the frame is resin) and the pole is styrene! SO, once the frame CA dried, I glued the ring to the pole with Tenax 7R! Then while that was sitting and drying, I worked on the firewall. Now this was FUN, as I had to make an identical copy of the one I made in my truck (in real life, on the 2 trucks, they would have been VERY close the same!) SO, I had to take my Power Wagon truck, and literally "copy" it, a second time! That looks pretty good (There is ONE, difference!) I had thought my Dad, (being "Dad") and thinking, I knew him, and I did....... BUT, in normal things with him, he would HAVE removed the A/C, for the power consumption it used. BUT to hear my uncle, he tells me Dad NEVER did it on this truck! Which, surprised me to hear, as I know for a fact this was one of VERY FEW that Dad didn't remove the A/C compressor from! SO, with the firewall detail, I'll be adding the heater core hoses and fittings (like I did on my truck, BUT I'll also be adding the A/C piping too, that runs from the compressor to the firewall! (Meaning, I'll have running pipe from the front of the compressor to a condensing radiator near the standard radiator!) SO, a little "extra" detail being added over-all, BUT the extra fittings to the firewall as well and I have yet to add them! So, while some of the paint was drying,and CA drying from the added wiring to the firewall. I got to working on the belt set up on the engine, A/C compressor added, as well as the power steering, and alternator. This all looks GREAT! Alternator is painted so, the internal wires are seen between the cooling ribs of its casing, as well as "drilled" for the wires that lead off of it, just as I did on my Power Wagon model. The blue wire runs to the coil, and back to the firewall. The red wire on the alternator runs to the battery, and across the radiator core support. (I have to get that all detailed up pretty soon too!) -and now to top it all off, I'm working on adding valve stems to the rims on Dads truck! I haven't yet gotten pics of that yet, BUT, they are drilled for them, and 2 or 3 have them in place! -Thought I'd let everyone know, I did choose to add them, as I said, they are drilled with having the hole smaller to "press fit" the valve stem, and because on Dads truck the tires are solid vinyl, I drill partly into them and press the wire "valve stem" into the vinyl to "grab" and hold in place without glue! More to come as progress happens! -Enjoy!
|
|